Furnace Repair in Delano, CA
Diagnosis and repair for gas, electric and packaged furnaces that won't light, won't stay on or can't keep the house warm, booked into a scheduled appointment window.
- Written Quote Before Any Work
- Gas, Electric & Packaged Furnaces
- Scheduled Appointment Window
In Delano, a furnace can sit unused from early spring until the first cool nights of late fall. During that long rest, dust settles on burners and flame sensors. Igniters and inducer motors that were already weak often fail the first time the heat comes back on.
We handle furnace repair in Delano, CA, from gas furnace repair on closet, garage and attic units to electric furnaces and rooftop packaged systems. Every repair starts with a diagnosis and a written quote you approve. Reach out through our contact page or call to book an appointment window.
Furnace or Heater Not Working? What Each Symptom Usually Means
These problems can usually be booked as a standard repair.
If you smell gas, a carbon monoxide alarm goes off, or the house is getting cold enough to put someone at risk, read the safety notes below first.
| Symptom | Usual causes | What we repair |
|---|---|---|
| Won't turn on | No power at the furnace switch or breaker, a blown low-voltage fuse, an open door safety switch, a failed control board, or no call for heat from the thermostat | Power and control faults, fuses, door switches, control boards, thermostat wiring |
| Runs but doesn't heat (blows cold air) | Burners not lighting: a failed igniter, dirty flame sensor, gas valve fault, or a pressure switch that won't close | Igniters, flame sensors, gas valves, pressure switches, the inducer circuit |
| Lights, then shuts off within seconds | The flame sensor can't prove the flame, so the board shuts the gas off, retries, then locks out. This is common after Delano's long off-season. | Flame sensor cleaning or replacement, burner and ground checks |
| Short cycling | Overheating from a clogged filter or weak blower that trips the high-limit switch, an oversized furnace, or a thermostat near a heat source | Blower motors, capacitors and wheels, limit switches, thermostat wiring |
| Runs constantly, house stays cool | Low burner firing, a dirty blower wheel, or attic ducts disconnected at the furnace | Burner pressure adjustment, blower cleaning, duct reconnection at the furnace |
| Weak airflow or cold rooms | A failing blower motor or capacitor, a packed blower wheel, or blocked returns | Blower motors, capacitors, wheels |
| Squealing or grinding | Worn blower or inducer motor bearings | Motor replacement |
| Yellow or wavering burner flames | Dirty burners, poor combustion air or a venting problem | Burner cleaning, venting repair, combustion and CO testing |
| Water around the furnace (90%+ models) | A clogged condensate trap or drain line, or a failed condensate pump | Traps, drain lines, pumps |
| Breaker trips when the furnace starts | A shorted motor, failing capacitor or wiring fault | Finding and repairing the electrical fault |
How a Scheduled Furnace Repair Visit Works
-
Booking
Reach out through our contact page or call. Tell us:
- The furnace type (gas, electric or packaged) and where it's installed: hall closet, garage, attic, roof, or a manufactured home
- The brand and age, if you know them
- What it's doing, and any blinking light pattern you can see through the furnace door
- When the filter was last changed, and whether SoCalGas left a notice on the furnace
- Access details such as a gate code, pets or where the attic hatch is
-
Appointment Window
We set a window for the visit and confirm it with you beforehand.
-
Arrival
The technician checks in, gets to the furnace and thermostat, and asks you to walk through what you've noticed and when it started.
-
Diagnosis
What we check:
- The full start-up sequence: call for heat, inducer, pressure switch, igniter, gas valve, flame proof
- Gas supply and burner pressure
- Flue and venting, plus the condensate trap and drain on 90%+ furnaces
- High-limit and rollout switches
- Blower motor, capacitor, wheel and airflow
- Control board, wiring and the thermostat signal
- Combustion and carbon monoxide readings when the symptoms point that way
-
Written Quote
You get the cause, the repair and the price in writing. Work starts after you approve it.
-
Repair, Testing and Cleanup
After the repair we run several full heating cycles, confirm the burner flame and safety switches, check the temperature rise at the supply, and clean the work area.
Furnace Repairs We Handle, by System
In Delano's dusty air, flame sensors and blower wheels are two of the first parts we check.
Ignition and Flame
Gas and Venting
Controls and Safety
Airflow
Condensate (90%+ Furnaces)
Electric Furnaces
Heat Exchanger
A cracked heat exchanger usually leads to a replacement conversation rather than a repair.
Furnace Error Lights and Blink Codes
Most modern gas furnaces have a status light on the control board, visible through a small window in the blower door. When something goes wrong, it flashes a pattern. The meaning depends on the make and model, and the code chart is usually printed on the furnace's access panel.
Count the flashes before you turn the furnace off, and tell us the pattern when you book. We treat the code as a starting point and confirm the cause with meter and pressure readings before replacing a part.
If your furnace is in an attic, as it is in some older Delano homes, a short phone video of the light works too.
Status light, through the blower door window
A pattern is a starting point — not the final word on what's wrong.
What Delano's Short Heating Season Does to a Furnace
Delano's average January low is about 38°F (NOAA 1991–2020 normals), so most furnaces here only run hard for a few months. During the idle months, dust settles on burners and flame sensors. Parts that were already weak last winter, like igniters and inducer motors, tend to quit on the first cold start.
First to fail:
- Igniters
- Inducer motors
Fog nights wear out blowers
From about November through February, tule fog brings long, damp, near-freezing nights, and those are the furnace's longest run times of the year. Worn blower motors and capacitors usually give out then.
First to fail:
- Blower motors
- Capacitors
Valley dust leads to short cycling
The San Joaquin Valley is a federal nonattainment area for fine particulates, and farm dust and Highway 99 grit load furnace filters quickly. A packed filter starves the blower, the heat exchanger runs hot, and the high-limit switch shuts the burners off. That's a common cause of short cycling.
Where it shows up:
- Filter
- Blower
- High-limit switch
Central AC adds year-round wear
If your furnace also serves a central AC, its blower runs through Delano's long cooling season too. The motor and capacitor wear all year, not just in winter.
First to fail:
- Blower motor
- Capacitor
Furnace Types and Locations We Repair in Delano
About two in three Delano homes heat with utility gas from SoCalGas, and about one in four use electricity (Census ACS 2020–2024). These are the furnace setups common in Delano homes. If you're not sure we work on yours, call and ask our pros.
-
Upflow gas furnaces in hall closets and garages
-
Horizontal gas furnaces in attics, where access affects the repair
-
Packaged gas/electric units on roofs or ground pads, where the burners and controls sit outdoors in the dust
-
Downflow furnaces in manufactured and mobile homes (about 4% of Delano homes), which need parts that match the manufactured-home model
-
Electric furnaces, with heating elements and sequencers instead of burners
-
Dual fuel systems: we repair the furnace side. For the outdoor unit, see the heat pump side of a dual fuel system.
Furnace Brands We Repair
We repair Carrier, Goodman and Lennox furnaces, along with other major brands.
- Carrier
- Goodman
- Lennox
- Other major brands
Some Delano furnaces are old enough that their original parts are discontinued. In those cases we use approved universal parts where the manufacturer allows it.
The model number on the furnace's rating label helps us bring the right igniter, sensor or board.
When a Repair Stops Making Sense
Most furnace problems come down to one failed part. When that's not the case, the technician will say so plainly.
Examples are
-
a cracked heat exchanger,
-
a fault that keeps coming back, or
-
a furnace whose parts are no longer made.
A Delano furnace runs only a few months a year, so age alone is a weaker reason to replace here than in a colder climate.
If replacement makes more sense, here are options for a new furnace.
How Furnace Repair Is Priced
As a general estimate, many common furnace repairs cost a few hundred dollars, and major part replacements can cost more than $1,000. These are general estimates, not actual prices. Your actual price depends on what failed and on your furnace.
What moves the price:
-
which part failed, and whether it's a universal or brand-specific part
-
where the furnace is: Delano attic and rooftop units take longer to reach than a hall closet
-
the furnace's age and how easy its parts are to get
-
whether the venting or a 90%+ furnace's condensate system is involved
-
whether the diagnosis turns up more than one fault
For actual prices, call and connect with our professionals.
Get Your Furnace DiagnosedGas Smells, CO Alarms and SoCalGas Shutoffs
Gas smell
-
Leave the home first.
-
Then call SoCalGas at +1-800-427-2200, or 911, from outside.
-
For repair help after that, see help when the heat can't wait.
-
Carbon monoxide alarm
California has required CO alarms in single-family homes with gas appliances since July 1, 2011. If yours sounds, follow the same steps as for a gas smell.
-
SoCalGas left the furnace off
If a SoCalGas technician turned your furnace off after a pilot relight or safety check, their notice tells you to have a qualified service company make the repair. That's a standard repair visit for us.
-
Blank thermostat
If the screen is blank or won't respond, see a thermostat that's blank or unresponsive.
Furnace Repair Questions from Delano Homeowners
Is a burning smell normal when I turn the furnace on for the first time this year?
A dusty burning smell for the first few minutes is common in Delano, because dust settles on the burners and heat exchanger during the long off-season. If it lasts past the first run, smells like hot plastic or wiring, or comes back every time the furnace starts, book a repair so we can find the overheating part. A gas odor is different: leave the home and call SoCalGas.
Why does my furnace light and then shut off after a few seconds?
Usually the flame sensor can't confirm the burners are lit, so the control board shuts off the gas as a safety step, retries, then locks out. A dirty or worn sensor is the most common cause, especially after a long idle season. We clean or replace the sensor and check the burner flame, gas pressure and ground connection.
Why is my furnace clicking but not lighting?
The clicking is usually the control board or a relay trying to start the sequence. If the inducer runs but the igniter never glows, the pressure switch may not be closing. On a 90%+ furnace, that can point to a blocked condensate drain or vent. If the igniter glows but the burners don't light, we check the gas valve and gas supply next.
What causes a furnace to short cycle?
The most common cause is overheating. A clogged filter or weak blower lets the heat exchanger get too hot, and the high-limit switch shuts the burners off. Other causes include a furnace that's too large for the house, a failing limit switch, or a thermostat mounted near a heat source. In Delano, dust-loaded filters and blower wheels are frequent contributors.
Why is one room cold when the furnace is running?
Common causes are a duct that's disconnected or crushed in the attic, a weak blower, a closed or blocked return, or a long duct run to that room. We check airflow at the furnace and at the room to find which one it is. When the problem is at the furnace connection, we reconnect or repair the duct there.
Can you repair a furnace that SoCalGas turned off?
Yes. When a SoCalGas technician leaves a furnace off because of a safety problem, we diagnose and repair what they flagged, then test the furnace before it goes back into service. Keep the notice they left. It tells us what they found.
Does furnace repair need a permit in Delano?
Most part-for-part repairs, such as replacing an igniter, flame sensor, motor or control board, generally don't. Replacing the whole furnace, or changing gas piping or venting, usually does. Requirements can vary by address, so call and ask our pros whether your repair needs one.
Do you repair furnaces in manufactured and mobile homes?
In most cases, yes. Manufactured homes typically use a downflow furnace in a closet that feeds ducts under the floor, and parts need to match the manufactured-home model. Call with the brand and model number from the furnace label, and our pros will confirm before the visit.
Do you repair electric furnaces?
Yes. Electric furnaces use heating elements, sequencers and limit switches instead of burners. Common repairs are a failed element, a sequencer that won't bring the elements on, or a tripped breaker. About one in four Delano homes heat with electricity, though some of those use heat pumps rather than furnaces.
Can my landlord or tenant set up the furnace repair?
Either one can reach out. About 37% of Delano homes are rentals (Census ACS 2020–2024), so we can work with both: the tenant for access and symptoms, and the owner for approving the written quote.
Furnace Repair Appointments in Delano
Tell us what your furnace is doing, where it's installed and its brand if you know it. We'll set an appointment window and send a technician to diagnose it.
- What it's doing
- Where it's installed
- Its brand, if you know it